

Appears AGH is running and using unbound but unbound is not using the DNS over TLS configuration? It states that DNS over TLS is not being used.

Unfortunately with either the above configuration and or the previous one when I visit There are a number of requests in the thread which states to follow the set up which I think I have done but still the own self status check does not work.ĥ - Services – DHCPv4 – : DNS Servers all blankĦ – Opnsense – Servies - Unbound DNS – Generalħ - Opnsense - Services - Unbound - Dns Over TlsĨ - Opnsense - Services - Unbound - Generalĩ - Navigate to ( 192.168.1.1:3000 ) to complete the setup Adguardġ0 - Adguard Home - DNS Configuration - Upstream Servers: Add router_ip:53530 ( 192.168.1.1:5353 ) Delete those that existġ1 – Adguard Home – DNS Configuration – Private reverse DNS servers Hi, I’m looking for some assistance as I’ve read the entire 12 pages and have not been able to get opnsense dns resolution working after the settings below are applied. Sorry my bad english, i use google translate. In this way the clients are forced to go from AG Guard which filters according to the rules, the DNS requests go through Unbound which takes care of contacting the servers for wan addresses and resolving the internal hosts.ĭo you confirm that this is the best configuration? Rule in the firewall to intercept all DNS requests from the LAN and redirect them to AD Guard to prevent "crafty" programs from bypassing the system. Upstream DNS servers: [/local.lan//2009OPNsense_IP:5353 OPNsense: System: Settings: General -> DNS servers -> blank (so everything is set to 127.0.0.1) Generally it is simply said do so and so without explaining why it is necessary that way.Ĭlient -> OPNsense -> AD Guard -> Unbound -> Internet Hi, I have read some guides and discussions.

Set the desired dns servers, ej, Cloudflare:Ħ - Opnsense - Services - Unbound - Generalħ - Navigate to ( 192.168.1.1:3000 ) to complete the setup AdguardĨ - Adguard Home - DNS Configuration - Upstream Servers: Add router_ip:5353 ( 192.168.1.1:5353 ) Delete those that exist Untick: Allow DNS server list to be overridden by DHCP/PPP on WANĥ - Opnsense - Services - Unbound - Dns Over Tls Untick: Do not use the local DNS service as a nameserver for this system
#PFSENSE ADGUARD HOME INSTALL#
It is very important to follow the order explainedġ - Activate mimugmail's community repositoryĢ - Install AdGuardHome from System -> Firmware -> Pluginsģ - Activate and start AdGuardHome from Services -> AdGuardHomeĤ - Opnsense - System - Settings -General Opnsense 22.1 Clean Install - Installation:

Quote from: yeraycito on January 28, 2022, 07:26:33 pm Thank you very much, I have tried it and it works. The firewall blocked access, by design, until I explicitly allowed those ports access from my LAN net to my LAN address. The latter showed no issues because there weren't any with the service. I figured it out when I looked where I should have in the first place - the firewall logs vs. Easy fix when I realized what the problem was. This means you need to explicitly define any additional ports (besides 80 and 443 which are in the default anti-lockout rule) you want to access on the OPNsense box itself, in this case 3000 (for the wizard) and then 81 (the port I picked AdGuardHome to run on). The problem, if anyone else runs in to this, is I am using a failover group for a gateway (my ISP WAN interface + backup LTE modem) and for that to work correctly the LAN "pass all outbound" rule has to be modified to use it vs. The service just appears to be running and waiting for me to kick off the process.Ĭould someone post a (more or less) "default" configuration yaml for the plugin? I can modify it for my own setup, restart the service, see if that gets past it, though I'd still like to figure out why I can't access the initial config wizard.Įdit: As often happens, writing this post made me re-think a couple things to try and I got it working. Since that triggers the initial setup wizard, there's no configuration yaml created (I checked via CLI). I cannot get the start page to come up at all on port 3000. Netstat shows the AdGuardHome service is running on said port and nothing else. I am not running Grafana, NTPng, or any other service on port 3000. The plugin is enabled and appears to be running Quote from: planetix on August 03, 2021, 04:32:34 pm Is there a known issue with fresh installs of this plugin and 21.7? I can't even get the setup page to load after a successful plugin install (http::3000).
